0.8mm Pitch Insulation Displacement Connector Housings With LCP Material A0800
1, Detailed specification:
1. Basic information:
- Color: light-yellow
- Row No.: single
- Circuits: 2pin to 22pin
- Plated:Gold-plated
- Insulation O.D.: 0.39mm
- Matched parts: A0800 series wafer
- Housing Material: LCP(Halogen free); standard PA46
- Contacts Material: phosphor bronze/tin-plated
- Mounting Type: Surface Mount
2. Electrical characteristic:
- Current Rating: 0.5A AC, DC(AWG#30); 0.2A AC, DC(AWG#36)
- Voltage Rating: 30V AC, DC
- Contact Resistance: 20mΩ Max
- Insulation Resistance: 100mΩ
- Withstanding Voltage: 200V AC/minute
3. Mechanical characteristic:
- Temperature Range:-25°C ~+85°C
Other detailed data please check the below pictures.
2, Related engineering drawing and testing report
The attached picture is our standard engineering drawing and report for your reference, it will help you to
know our product feature, then you can choose the right models.
|
3. Ratings & Applicable Wires
| Item |
Standard |
| Rated Voltage (Max.) |
30V AC/DC |
Insulation O.D. 0.38mm (Max.) |
| Rated Current (Max.) And Applicable Wires |
AWG#32 0.5A AC/DC |
| Ambient Temperature Range |
-25℃ ~ +85℃ |
*: Including terminal temperature rise
4. Electrical Performance
| Test Description |
Procedure |
Requirement |
| 4-1 |
Contact Resistance
|
Mate connectors, measure by dry circuit, 20mV max., 10mA.(Based upon JIS C5402 5.4) |
20mΩ (Max.) |
| 4-2 |
Insulation Resistance |
Mate connectors, apply 500V DC between adjacent terminal or ground. (Based upon JIS C5402 5.2/MIL-STD-202 Method 302 Cond. B) |
100MΩ (Min.) |
| 4-3 |
Dielectric Withstanding Voltage |
Mate connectors, apply 200V AC (rms) for 1 minute between adjacent terminal or ground. (Based upon JIS C5402 5.1/MIL-STD-202 Method 301) |
No Breakdown. |
| 4-4 |
Contact Resistance on Crimped Portion |
Crimp the applicable wire on to the terminal, measure by dry circuit, 20mV (Max.)., 10mA. |
5mΩ (Max.) |
5. Mechanical Performance
| Test Description |
Procedure |
Requirement |
| 5-1 |
Actuator Insertion & Withdrawal Force |
Insert and withdraw connectors at the speed rate of 25±3mm / minute. |
Refer to paragraph 7 |
| 5-2 |
Wire pull Out Force |
Pulling load shall be applied to a correctly terminated wire in parallel and perpendicular directions. The load to pull the wire out of the socket or break the wire shall be measured. |
Parallel direction |
Perpendicular direction |
| 0.30 kgf(Min.) |
0.15 kgf(Min.) |
| 5-3 |
Terminal/Housing Retention Force. |
Apply axial pull out force at the speed rate of 25±3mm / minute on the terminal assembled in the housing. |
0.25kgf (Min.) |
| 5-4 |
Pin Retention Force |
Apply axial push force at the speed rate of 25±3mm / minute |
0.25kgf (Min.) |
| 5-5 |
Durability |
When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute. |
Contact Resistance 40mΩ (Max.) |
| 5-6 |
Vibration |
Amplitude: 1.5mm P-P
Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes.
(Based upon MIL-STD-202 Method 201A)
|
Appearance No Damage.
Contact Resistance 40mΩ (Max.)
Discontinuity 1 μsec.(Max.)
|
| 5-7 |
Physical Shock |
490m/s²｛50G｝,3 strokes in each X.Y.Z. axes. (Based upon JIS C0041/MIL-STD-202 Method 213B Cond. A) |
|
|
6. Environmental Performance And Others
| Test Description |
Procedure |
Requirement |
| 6-1 |
Temperature Rise |
Carrying rated current load.(Based upon UL 498) |
30℃(Max.) |
| 6-2 |
Heat Resistance |
85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) |
Appearance No Damage.
Contact Resistance 40mΩ (Max.)
|
| 6-3 |
Cold Resistance |
-25±3℃,96 hours (Based upon JIS C0020) |
| 6-4 |
Humidity |
Temperature: 40±2℃
Relative Humidity : 90~95%
Duration: 96 hours
(Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B)
|
Appearance No Damage.
Contact Resistance 40mΩ (Max.)
Insulation Resistance 10MΩ (Min.)
Dielectric Withstanding Voltage Must meet 4-3
|
| 6-5 |
Temperature Cycling |
5 cycles of:
a) -55℃ 30 minutes
b) +85℃ 30 minutes
(Based upon JIS C0025)
|
Appearance No Damage.
Contact Resistance 40mΩ (Max.)
|
| 6-6 |
Salt Spray |
Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt spray from the 5±1% solution at 35±2℃. (Based upon JIS C0023/MIL-STD-202 Method 101C Cond. B) |
| 6-7 |
SO2 Gas |
24 hours exposure to 50±5ppm.
SO2 gas at 40±2℃.
|
| 6-8 |
NH3 Gas |
40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. |
| 6-9 |
Solderability |
Soldering Time: 5±0.5 sec.
Solder Temperature: 245±5℃
|
Solder Wetting 95% of immersed area must show no voids, pin holes |
| 6-10 |
Resistance to Soldering Heat |
When reflowing
Refer to paragraph 8
Solder iron method
Soldering Time: 5±0.5 sec.
Solder Temperature: 370℃ ~ 400℃
|
Appearance No Damage. |
7. Actuator Insertion/Withdrawal Force
[Unit : kgf]
| Circuits |
At Initial |
Circuits |
At Initial |
| Insertion (Max.) |
Withdrawal (Min.) |
Insertion (Max.) |
Withdrawal (Min.) |
| 02 |
0.50 |
0.10 |
14 |
1.70 |
0.34 |
| 04 |
0.70 |
0.14 |
15 |
1.80 |
0.36 |
| 08 |
1.10 |
0.22 |
16 |
1.90 |
0.38 |
| 10 |
1.30 |
0.26 |
17 |
2.00 |
0.40 |
| 12 |
1.50 |
0.30 |
20 |
2.30 |
0.46 |
|
3, FAQ
1) What's the delivery time?
Usually 5-8 working days after payment checked, longer for large order.
2) What’s the payment term?
Our payment terms: T/T, PayPal, Western Union, Moneygram, L/C, etc.
3) What's the shipping way?
Via DHL, FedEx, EMS, UPS, by air, by sea...etc.
4) Do you have after-sales service?
Yes. 8 hours online service
5) What is your guarantee for the goods?
We will replace 1:1 for the defective goods after sales.12 months guarantee after manufacturing.
